These are the edge profiles we fabricate on 20 mm (3/4") natural and engineered stone. Each drawing shows a short piece of countertop, so you can see how the edge looks along the counter, with its cross-section and finished height underneath. On 40 mm edges, the thin line shows where the 20 mm strip is laminated under the slab. Please include the profile number when you send us your selections.
Shaped on the slab itself, for a finished edge height of 20 mm. The underside is polished 1 1/4" in from the edge.
A 20 mm strip is laminated under the slab for a 40 mm finished edge.
Built-up: 20 mm slab + 20 mm strip under the edge (1" deep), with top bevel.
Bevel size can be adjustedBuilt-up: 20 mm slab + 20 mm strip under the edge (1" deep), with bevel on the bottom of the edge (the strip's outer corner).
Built-up: 20 mm slab + 20 mm strip under the edge (1" deep), 3/4" radius on the top.
Built-up: 20 mm slab + 20 mm strip under the edge (1 1/2" deep); the face slopes back the full 40 mm at 30 deg from upright, 5/32" rounds top and bottom.
Built-up: 20 mm slab + 20 mm strip under the edge (1 1/2" deep); the face slopes forward the full 40 mm at 30 deg from upright, 5/32" rounds top and bottom.
Built-up: 20 mm slab + 20 mm strip under the edge (1" deep), a 3/4" bevel on the slab, ending at the seam.
Bevels, ogee, V-groove, cove, and the mitred edge.
Built-up: 20 mm slab + 20 mm strip under the edge (1" deep), 1/4" bevels on the top and the bottom of the edge.
Built-up: 20 mm slab + 20 mm strip under the edge (1" deep); ogee on the slab, the two pieces flush where they meet.
Built-up: 20 mm slab + 20 mm strip under the edge (1" deep); a V-groove at the seam (1/4" bevels on both pieces), square top.
Built-up: 20 mm slab + 20 mm strip under the edge (1" deep), cove on the slab.
Mitred: a 20 mm apron mitred to the slab, 40 mm finished height.
Curves only with certain quartzThe strip steps out or in about 3/16" from the slab for a shadow line, plus the full and ogee bullnose.
Built-up: 20 mm slab + 20 mm strip under the edge (1" deep), quarter round (3/4" rad) on the slab; the strip steps out 3/16" past the slab.
Built-up: 20 mm slab + 20 mm strip under the edge (1" deep), ogee on the slab; the strip steps out 3/16" past the slab.
Built-up: 20 mm slab + 20 mm strip under the edge (1" deep), top bevel (1/4") on the slab; the strip steps out 3/16" past the slab.
Built-up: 20 mm slab + 20 mm strip under the edge (1" deep), one 20 mm radius round over the full 40 mm.
Built-up: 20 mm slab + 20 mm strip under the edge (1" deep), quarter round (3/4" rad) on the slab; the strip steps in 3/16" from the slab.
Built-up: 20 mm slab + 20 mm strip under the edge (1" deep), ogee on the slab; the strip steps in 3/16" from the slab.
Built-up: 20 mm slab + 20 mm strip under the edge (1" deep), top bevel (1/4") on the slab; the strip steps in 3/16" from the slab.
Built-up: 20 mm slab + 20 mm strip under the edge (1" deep), cove on the slab; the strip steps out 3/16" past the slab.
Built-up: 20 mm slab + 20 mm strip under the edge (1" deep), cove on the slab; the strip steps in 3/16" from the slab.
Built-up: 20 mm slab + 20 mm strip under the edge (1" deep); ogee on the slab, the strip rounded back to the bottom (20 mm radius).
A shaped slab over a rounded strip, plus the mitred bevel and stepped bevels.
Built-up: 20 mm slab + 20 mm strip under the edge (1" deep); quarter round (3/4" rad) on the slab; the strip a 3/8" half bullnose, sticking out 3/8" so there's no gap under the slab.
Built-up: 20 mm slab + 20 mm strip under the edge (1" deep); ogee on the slab; the strip a 3/8" half bullnose, sticking out 3/8" so there's no gap under the slab.
Built-up: 20 mm slab + 20 mm strip under the edge (1" deep); top bevel (1/4") on the slab; the strip a 3/8" half bullnose, sticking out 3/8" so there's no gap under the slab.
Built-up: 20 mm slab + 20 mm strip under the edge (1" deep); half bullnose (3/8" rad) on the slab; the strip a full bullnose, sticking out 10 mm so there's no gap under the slab.
Built-up: 20 mm slab + 20 mm strip under the edge (1" deep); ogee on the slab; the strip a full bullnose, sticking out 10 mm so there's no gap under the slab.
Built-up: 20 mm slab + 20 mm strip under the edge (1" deep); top bevel (1/4") on the slab; the strip a full bullnose, sticking out 10 mm so there's no gap under the slab.
Built-up: 20 mm slab + 20 mm strip under the edge (1" deep); cove on the slab; the strip a 3/8" half bullnose, sticking out 3/8" so there's no gap under the slab.
Built-up: 20 mm slab + 20 mm strip under the edge (1" deep); cove on the slab; the strip a full bullnose, sticking out 10 mm so there's no gap under the slab.
Mitred: a 20 mm apron mitred to the slab, 40 mm finished height, 1/4" bevel on the top.
Curves only with certain quartzBuilt-up: 20 mm slab + 20 mm strip under the edge (1" deep), a 1/2" bevel on the slab and a 3/16" bevel on the strip, the strip steps out 3/16" past the slab.
Call or email us and we'll help you choose. The edge you pick can also affect the price.
